General Rules for Safe Operation Personal Protection
1. Personal Protective Equipment
1. Always wear: chemical-resistant nitrile gloves.
2. It is highly recommended to wear: goggles (to prevent resin from splashing into the eyes) and a mask when working in a poorly ventilated environment.
2. Operating Environment
1. Ventilation: Ensure good ventilation in the work area and keep it away from light.
2. Fire prohibition: Keep away from open flames and heat sources.
3. Cleanliness: Keep the work area tidy and ensure there are sufficient lint-free cleaning cloths and alcohol available.
3. Emergency Handling
1. Skin contact: If the product accidentally comes into contact with clothing, remove the contaminated clothing immediately. If it comes into contact with the skin, rinse thoroughly with plenty of soap and water for at least 15 minutes immediately. Seek medical attention if irritation persists.
2. Eye contact: If the resin accidentally comes into contact with your eyes, immediately rinse them with plenty of water for 30 minutes and seek medical attention right away.
3. Spill: Absorb with absorbent pads or paper towels, place in a sealed bag for disposal as chemical waste. Thoroughly clean the contaminated surface with alcohol.
Specifications for the Whole Usage Process
1. Commissioning and Preparation of New Resin
• Preheating: If the resin is stored in a low-temperature environment (<20°C), immerse the sealed resin bottle in warm water below 40°C for 10-15 minutes before use to reach the optimal operating temperature. Do not heat it directly or in a microwave oven.
• Resin Shaking: After tightening the bottle cap, shake vigorously for 2-3 minutes or use a dedicated resin shaker to ensure all precipitates at the bottom of the bottle are fully and evenly suspended. The criterion for judgment is that the liquid has a uniform color and texture, with no stratification or precipitation streaks.
• For continuous printing or resuming printing after the resin in the resin tank has been left standing for a period of time: fully stir the resin in the resin tank with a clean plastic spatula or other non-sharp tool before starting printing.
2. Precautions During the Printing Process
• Resin volume in the tank: Ensure that the resin liquid level does not exceed the MAX maximum capacity scale line in the tank to avoid contamination caused by resin overflow during printing.
• Avoid contamination: Ensure that the plastic spatula used for stirring the resin in the trough and the tools for recovering the recycled resin are completely clean, so as to prevent the mixing of different resins, alcohol, and alcohol-resin mixtures, which may cause cross-contamination and abnormal curing.
3. Resin Recovery and Cleaning After Printing
• Filtration and Recovery: After printing is completed, if you need to pour the resin back into storage, you must use a new disposable paper filter funnel for filtration, so as to avoid printing failure and damage to the release film and printing screen caused by any tiny cured debris during the printing process.
• Cleaning Tools: All tools that have come into contact with resin (such as scrapers, funnels, beakers, etc.) shall be cleaned immediately with 95% concentration industrial alcohol after use.
Storage and Lifecycle Management
1. Storage Environment
1. Temperature: The optimal storage temperature ranges from 20 to 25 degrees Celsius.
2. Light protection: Must be stored in the original opaque black bottle and kept in a cool, dark place. Normal ambient light (especially ultraviolet rays) will cause slow pre-curing of the resin.
3. Sealing: Tighten the bottle cap immediately after each use to reduce the emission of pungent odors.
2. Validity Period and Status Judgment
1. Label Instructions: Record the opening date on the bottle label. It is recommended to use up the resin within 3 months after opening.
2. Signs of failure: When any of the following occurs, the resin performance has deteriorated severely, and it is not recommended to continue using it for critical printing:
• Abnormal increase in viscosity
• A large amount of non-dissipating particles or gel-like substances appears
• Poor performance after curing
3. Test Print: If you have doubts about the condition of the used resin, you can first print a simple test model (such as a calibration cube) to verify its curing status and strength.
3. Waste Disposal: Please follow local laws and regulations for specific operations; the following operational suggestions are for reference only.
1. Liquid resin: Dispose of it as hazardous chemical waste. Do not pour it directly into drains. You can leave it in the sun to fully cure it, then discard it as solid waste, or contact a professional agency for recycling.
2. Cured resin: A fully cured resin model is an inert solid and can be disposed of as ordinary waste.
Resin Management Label Recommended to be affixed to storage cabinets or work areas
|
Project |
Suggest |
|---|---|
|
Personal Protective Equipment |
Wear nitrile gloves, goggles and a mask |
|
Enable Preparation |
Shake well |
|
transfer process |
Use a filter funnel |
|
Operating Environment |
Keep in a well-ventilated, light-proof environment with an ambient temperature of 20-25°C |
|
Storage Requirements |
Store in a cool, dry place away from direct sunlight and keep sealed tightly |
